8.26. GCC-10.2.0

8.26.1. Installation of GCC

On 64-bit hosts, set the default directory name for 64-bit libraries to “lib”:

sed -e 's/lib64/lib/g' \
       -i.orig $(find gcc/config -name t-linux64)

On 64-bit MIPS, set the default directory name for core C runtime objects to “lib”:

sed -e 's/lib64/lib/g' \
       -i.orig gcc/config/mips/mips.h

Fix an issue on MIPS:

sed -e '2384 s/MSA/mode != MAX_MACHINE_MODE \&\& &/' \
     -i gcc/config/mips/mips.c

The GCC documentation recommends building GCC in a dedicated build directory:

mkdir -v build
cd       build

Prepare GCC for compilation:

../configure --prefix=/usr            \
             LD=ld                    \
             --enable-languages=c,c++ \
             --disable-multilib       \
             --disable-bootstrap      \
             --with-system-zlib       \
             --with-abi=64            \
             $LFS_MIPS_GCC_EXTRA_OPTIONS

Note that for other programming languages there are some prerequisites that are not yet available. See the BLFS Book GCC page for instructions on how to build all of GCC's supported languages.

Compile the package:

make

One set of tests in the GCC test suite is known to exhaust the default stack, so increase the stack size prior to running the tests:

ulimit -s 32768

Test the results as a non-privileged user, but do not stop at errors:

chown -Rv tester . 
su tester -c "PATH=$PATH make -k check"

To receive a summary of the test suite results, run:

../contrib/test_summary

For only the summaries, pipe the output through grep -A7 Summ.

Results can be compared with those located at http://www.linuxfromscratch.org/lfs/build-logs/10.1-mips64el/ and https://gcc.gnu.org/ml/gcc-testresults/.

Six tests related to get_time are known to fail. These are apparently related to the en_HK locale.

Additionally the following tests related to the following files are known to fail with glibc-2.33: asan_test.C, co-ret-17-void-ret-coro.C, pr95519-05-gro.C, pr80166.c.

A few unexpected failures cannot always be avoided. The GCC developers are usually aware of these issues, but have not resolved them yet. Unless the test results are vastly different from those at the above URL, it is safe to continue.

Install the package and remove an unneeded directory:

make install
rm -rf /usr/lib/gcc/$(gcc -dumpmachine)/10.2.0/include-fixed/bits/

The GCC build directory is owned by tester now and the ownership of the installed header directory (and its content) will be incorrect. Change the ownership to root user and group:

chown -v -R root:root \
    /usr/lib/gcc/*linux-gnu*/10.2.0/include{,-fixed}

Create a symlink required by the FHS for "historical" reasons.

ln -sv ../usr/bin/cpp /lib

Add a compatibility symlink to enable building programs with Link Time Optimization (LTO):

ln -sfv ../../libexec/gcc/$(gcc -dumpmachine)/10.2.0/liblto_plugin.so \
        /usr/lib/bfd-plugins/

Now that our final toolchain is in place, it is important to again ensure that compiling and linking will work as expected. We do this by performing some sanity checks:

echo 'int main(){}' > dummy.c
cc dummy.c -v -Wl,--verbose &> dummy.log
readelf -l a.out | grep ': /lib'

There should be no errors, and the output of the last command will be (allowing for platform-specific differences in the dynamic linker name):

[Requesting program interpreter: /lib64/ld.so.1]

Now make sure that we're setup to use the correct start files:

grep -o '/usr/lib.*/crt[1in].*succeeded' dummy.log

The output of the last command should be:

/usr/lib/gcc/mips64el-unknown-linux-gnuabi64/10.2.0/../../../../lib/crt1.o succeeded
/usr/lib/gcc/mips64el-unknown-linux-gnuabi64/10.2.0/../../../../lib/crti.o succeeded
/usr/lib/gcc/mips64el-unknown-linux-gnuabi64/10.2.0/../../../../lib/crtn.o succeeded

Depending on your machine architecture, the above may differ slightly. The difference will be the name of the directory after /usr/lib/gcc. The important thing to look for here is that gcc has found all three crt*.o files under the /usr/lib directory.

Verify that the compiler is searching for the correct header files:

grep -B4 '^ /usr/include' dummy.log

This command should return the following output:

#include <...> search starts here:
 /usr/lib/gcc/mips64el-unknown-linux-gnuabi64/10.2.0/include
 /usr/local/include
 /usr/lib/gcc/mips64el-unknown-linux-gnuabi64/10.2.0/include-fixed
 /usr/include

Again, the directory named after your target triplet may be different than the above, depending on your system architecture.

Next, verify that the new linker is being used with the correct search paths:

grep 'SEARCH.*/usr/lib' dummy.log |sed 's|; |\n|g'

References to paths that have components with '-linux-gnu' should be ignored, but otherwise the output of the last command should be:

SEARCH_DIR("/usr/mips64el-unknown-linux-gnuabi64/lib64")
SEARCH_DIR("/usr/local/lib64")
SEARCH_DIR("/lib64")
SEARCH_DIR("/usr/lib64")
SEARCH_DIR("/usr/mips64el-unknown-linux-gnuabi64/lib")
SEARCH_DIR("/usr/local/lib")
SEARCH_DIR("/lib")
SEARCH_DIR("/usr/lib");

Next make sure that we're using the correct libc:

grep "/lib.*/libc.so.6 " dummy.log

The output of the last command should be:

attempt to open /lib/libc.so.6 succeeded

Make sure GCC is using the correct dynamic linker:

grep found dummy.log

The output of the last command should be (allowing for platform-specific differences in dynamic linker name):

found ld.so.1 at /lib/ld.so.1

If the output does not appear as shown above or is not received at all, then something is seriously wrong. Investigate and retrace the steps to find out where the problem is and correct it. Any issues will need to be resolved before continuing with the process.

Once everything is working correctly, clean up the test files:

rm -v dummy.c a.out dummy.log

Finally, move a misplaced file:

mkdir -pv /usr/share/gdb/auto-load/usr/lib
mv -v /usr/lib/*gdb.py /usr/share/gdb/auto-load/usr/lib